Integra 5.1 receiver manual

Page Speaker Setup Speaker setup Follow the steps below before you start operating the unit. Select the size of the center speaker. Page 16 Speaker setup 3. Page Selecting A Sound Source Selecting a sound source Follow the steps below to select a device to play the sound source. Make sure that the Speakers A indicator is lit on the display. If it is not lit, press the Speakers A button. Follow the steps 1—4 below. This is not a malfunction. Page 22 To play a Dolby digital or DTS Surround source, you need to connect the sound source using the digital input connector.

Press the MODE Page 23 Using Listening Mode Main unit operation: 1. Press the CH Level button. Press the Enter button to select a speaker. Setting the Listening mode parameters The following parameters are available for each Listening mode. Select the tuner as the source by pressing the AM or 2. Make sure that you have made a correct analog connection.

If you select another device as the input source during recording, the input signal from that device will be recorded.

Speaker A Main room Page Using The Remote Controller When you use a remote controller, typically you press one of the MODE buttons that corresponds to the device you wish to control, then press the operation buttons. For example, if you wish to control the DTR Press the desired CD operation button. See page 9. Press the desired tape deck operation button. TAPE operation buttons Operate the programmed button to make sure the learning function works.

You may program other remote controller codes into these buttons. Page 35 Programming the remote controller codes of other devices into the RCM See page 39 for information on how to erase the learned codes from all buttons. Page Using A Macro Function A Macro function enables you to program a series of button operations on the remote controller into a single button. Check to see if the button has been programmed correctly.

Transmitting the codes in Macro mode takes a while. Press and hold down the corresponding MODE button 1, 2 2. RCM 1. Press and hold down any one of the MODE buttons 2.

Page Troubleshooting Guide Turn the power button off and then on again or remove the AC plug from the outlet and then plug it again. RMS at 8 ohms, 2 channels driven from 20 Hz to 20 kHz with no more than 0.

RMS at 6 ohms, 2 channels driven from 1 kHz with no more than 0. Standby indicator [5, 11] 2. See page 9 for more informa- tion. Tel: Fax: E-mail: integra onkyousa. Print page 1 Print document 44 pages. Rename the bookmark. Delete bookmark? Cancel Delete. Delete from my manuals? Sign In OR. Don't have an account? Sign up! Restore password. Upload manual. Upload from disk. Water and Moisture — The appliance should not be used near water — for example, near a bathtub, washbowl, kitchen sink, laundry tub, in a wet basement, or near a swimming pool, and the like.

Carts and Stands — The appliance should be used only with a cart or stand that is recommended by the manufacturer. An appliance and cart combination should be moved with care. Quick stops, excessive force, and uneven surfaces may cause the appliance and cart combination to overturn. Nonuse Periods — The power cord of the appliance should be unplugged from the outlet when left unused for a long period of time.

Object and Liquid Entry — Care should be taken so that objects do not fall and liquids are not spilled into the enclosure through openings. The power-supply cord or the plug has been damaged; or. Objects have fallen, or liquid has been spilled into the appliance; or. The appliance has been exposed to rain; or. The appliance does not appear to operate normally or exhibits a marked change in performance; or.

The appliance has been dropped, or the enclosure damaged. Servicing — The user should not attempt to service the appliance beyond that described in the operating instructions. Outdoor Antenna Grounding — If an outside antenna is connected to the receiver, be sure the antenna system is grounded so as to provide some protection against voltage surges and built up static charges.

See Figure 1. In case of warranty claim, please report this number. Recording of copyrighted material for other than personal use is illegal without permission of the copyright holder. The fuse is located inside the chassis and is not user-ser- viceable. If power does not come on, contact your Onkyo authorized service station. From time to time you should wipe the front and rear panels and the cabinet with a soft cloth. For heavier dirt, dampen a soft cloth in a weak solution of mild detergent and water, wring it out dry, and wipe off the dirt.

Following this, dry immediately with a clean cloth. The voltage of the available power supply differs according to country or region. Be sure that the power supply voltage of the area where this unit will be used meets the required voltage e. These limits are designed to provide reasonable protection against harmful interference in a residential installation.

This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:.

US Pat. All rights reserved. This unit does not require memory preservation batteries. A built-in memory power back-up system preserves the contents of the memory during power failures and even when the Power switch is set to off. The Power switch must be set to on in order to charge the back-up system. The memory preservation period after the unit has been turned off varies depending on climate and placement of the unit. On the average, memory contents are protected over a period of a few weeks after the last time the unit has been turned off.

This period is shorter when the unit is exposed to a very humid climate. Remove the battery compartment cover by pressing and sliding it out. After batteries are installed and seated correctly, replace the compartment cover.

The Standby indicator lights up when the unit receives a signal from the remote controller. The buttons of the remote controller may be pressed by mistake and drain the batteries. Placing the unit behind such doors may prevent proper remote controller operation. Remember that improper connection can result in noise, poor performance, or damage to the equipment. Improper connection.

Insert completely. See page If this interference occurs, place the receiver and the TV as far apart as possible. When this jack is not used, replace the protective cap. You may connect the 5. Use the DVD player or decoder controls to adjust the speaker settings for multi-channel input. You can connect the power cord from another audio device to the rear of this receiver.

First turn the Power switch On On. Make sure that the total capacity of other components connected to this unit does not exceed the capacity that is printed on the rear panel. For this model, the capacity is total watts. Plug-in the other end of the cable to a wall AC outlet. Connections for remote control.

For the best results, connect a center speaker. Please check the following information and choose speakers with appropriate impedances for the connections.

Speaker placement plays an important role in the reproduction of Surround sound. The placement of the speakers varies depending on the size of the room and the wall coverings used in the room. The illustration shows an example of a layout for standard speaker placement. Refer to this example when you position the speakers in order to experience the best of Surround sound. For ideal Surround effects, all speakers should be installed.

If a center speaker or subwoofer is not connected, the sound from the unused channel is properly distributed to the connected speakers in order to produce the best Surround sound possible.

Front: The left, right, and center speakers should face the seated listener and be placed at ear level. These speakers produce the feel of a moving sound while creating the sensation of being in the middle of the action.

If this happens, use a wall outlet on a different circuit. Plug the power cable into an AC wall outlet. When the DTR Therefore, when you plug in the power cord to the AC outlet, the Standby indicator lights up and the unit enters Standby mode as described in Step 2.

Press the Power switch to set it to the On position to place the receiver in Standby mode. Press the Power switch again to set it to the Off position to turn off the power to the receiver. The display will light up and the Standby indicator will be turned off. Press the Power switch of the DTR Press the On button to turn on the power to the DTR- 5. The FM indoor antenna is for indoor use only.

Extend the antenna and move it in various directions until the clearest signal is received. Fix it with push pins or similar implements in the position that will cause the least amount of distortion. If the reception is not very clear with the attached FM indoor antenna, the use of an outdoor antenna is recommended.

Remove the insulation at the tip of the cable, and insert the cable securely, fully to the end of the exposed tip. The AM loop antenna is for indoor use only.

Set it in the direction and position where you receive the clearest sound. Put it as far away as possible from the unit, TVs, speaker cables, and power cords.

When reception is not satisfactory with the attached AM loop antenna alone, connection of an outdoor antenna is recommended. FM Please make sure that you follow the considerations below regarding the location. It is dangerous to put the antenna close to power lines. Keep it well away from power lines, transformers, etc. The outdoor antenna will be more effective if it is stretched horizontally above a window or outside.

Welcome to ManualMachine.